MAX7057ASE+T【PDF 13/20 页】IC TRANSMITTER ASK/FSK 16-SOIC

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录55

9页 10页 11页 12页 [13页]14页 15页 16页 17页

Using a byte descriptive notation, the reset command

can be viewed as the following sequence, within the

same CS cycle:

SDI:

<0x04>

Features and Settings

Values and parameters are set through registers in the

MAX7057 that are addressable through the SPI. These

registers contain bits that either turn functions on and

off or program numerical settings. The following set-

tings are controlled through the SPI.

Variable Capacitor

The internal variable shunt capacitor, which is instru-

mental in matching the PA to the antenna, is controlled

by setting 5 bits in the configuration 0 register. This

allows for 32 levels of shunt capacitance control. Since

the control of these 5 bits is independent of the other

settings, any capacitance value can be chosen at any

frequency, making it possible to maintain maximum

transmitter efficiency while moving rapidly from one fre-

quency to another.

Clock Output

The MAX7057 has a buffered clock output that can

serve as a clock for a microprocessor. The divide ratio

is set through the configuration 0 register (see Tables 5

and 6). The divide settings are 1 (no division), 2, 4, 8, or

16; the original undivided frequency is based on the

reference frequency generated by the external crystal.

The buffered clock output is available at GPO when

enabled by setting the configuration 1 register (see

Tables 2, 3, 15, and 16).

Mode Select and Crystal Shutdown

The transmission mode is selected by writing to a regis-

ter. The default mode is ASK and the mode can be

changed to FSK by writing a 1 to the mode bit in the

control register. This register is also used to keep the

crystal circuit powered up in the shutdown mode.

Registers

The following tables provide information on the

MAX7057 registers.

300MHz to 450MHz Frequency-Programmable

ASK/FSK Transmitter

______________________________________________________________________________________ 13

SDI

SCLK

RESET COMMAND (0x04)

ADDRESS

DESCRIPTION

0x00

CONTRL

Control register. Controls the mode (ASK/FSK), crystal clock output, envelope-shaping, PLL

bandwidth, and SPI enable.

0x01

CONFIG0

Configuration 0 register. Controls the capacitance at the PA output and clock output

frequency divider.

0x02

HIFREQ1

High-frequency 1 register (upper byte). Sets the high frequency in FSK transmission.

0x03

HIFREQ0

High-frequency 0 register (lower byte). Sets the high frequency in FSK transmission.

0x04

LOFREQ1

Low-frequency 1 register (upper byte). Sets the low frequency in FSK transmission, or

carrier frequency in ASK transmission.

0x05

LOFREQ0

Low-frequency 0 register (lower byte). Sets the low frequency in FSK transmission, or carrier

frequency in ASK transmission.

0x06

FLOAD

Frequency load register. Performs the frequency load function.

0x07

DATAIN

Data in register. SPI equivalent of DIN pin.

0x08

Enable register. SPI equivalent of ENABLE pin.

0x09

CONFIG1

Configuration 1 register. GPO selector.

0x0C

STATUS

Status register.

Figure 6. Reset Command Format

Table 2. Register Summary

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式